Enter SPECIAL5 at Checkout for 5% OFF & Free Shipping Australia Wide

{"id":6614092578879,"title":"ANCEL BA301 6V 12V Battery Load Tester Car Alternator Analyzer Cranking Charging System Test Tool for Motorcycle Car Boat Light Truck and More","handle":"ancel-ba301-6v-12v-battery-load-tester-car-alternator-analyzer-cranking-charging-system-test-tool-for-motorcycle-car-boat-light-truck-and-more","description":"\u003ch3\u003eANCEL BA301 6V 12V Battery Load Tester Car Alternator Analyzer Cranking Charging System Test Tool for Motorcycle Car Boat Light Truck and More\u003c\/h3\u003e\n\u003cp id=\"b\"\u003eANCEL BA301 battery tester adopts the state-of-the-art\nconductance testing technology to measure the actual cold cranking amps\ncapability of starting battery, battery health status, and common fault of\nstarting system and charging system quickly and accurately. It works on all\nautomotive 6V \u0026amp; 12V 100-2000 CCA lead-acid batteries of car, motorcycle, light\ntruck, and more, including regular flooded, AGM flat plate, AGM spiral, GEL,\nand EFB batteries. And it features the \"Waveform\" menu and a hot-key on the\ndevice to monitors real-time voltage. This tool lets you know the battery\nstatus in advance and replace with a new battery in time, save a trip, and\nmoney to an auto repair shop. The test result includes 5 kinds of battery\nstatus and possible causes: 1. Good Battery The battery is without any\nproblem, please be relaxed to use. 2. Good, Recharge Good battery but low\ncurrent, recharge before using. 3. Replace The battery is near to or already\nreached the end of the using life, please replace the battery. Otherwise,\nbigger danger will be followed. 4. Bad cell, Replace Battery interior damaged,\nbad cell or short circuit, replace battery. 5. Charge, Retest Unstable battery\nshall be recharged and retested to avoid error. If the same test result\nappears after recharge and retest, the battery is regarded as damaged, replace\nthe battery. BATTERY CHECK Check 6V Motorcycle Battery BA301 battery analyzer\nworks on not the 12V battery of the automotive but also the 6V battery of the\nmotorcycle. Select motorcycle battery model and it takes around 1 second to\ndisplay the test result, including battery condition, the status of health,\ninternal resistance(mΩ), measured CCA, standard battery model, voltage value.\nANCEL BA301 Battery Tester Highlights: 1. Work on 6V \u0026amp; 12V 100-2000 CCA\nbattery 2. Check battery health status 3. Cranking test \u0026amp; Charging test 4.\nMonitor real-time voltage in Waveform 5. Get a accurate test results in merely\nseconds 6. Able to store, review, print the test result 7. Voltage measurement\nrange: 6-16V DC 8. Free lifetime update CANNOT test lithium battery and solar\nbattery No internal battery required and gets power directly from the detected\nbattery Test the battery with loss of electricity directly, a full charge is\nnot required before testing Read more Cranking Test The cranking test is used\nto test and analyze the actual required cranking current and cranking voltage\nto check the starting motor works properly or not. The test result displays\ncranking time, voltage, and status. If the stating malfunction may cause an\nincreased starting loaded torque; or rotor friction of the starting motor\ngenerates increasing friction of the starting motor itself Charging Test\nCharging test is used to check and analyze the charging system (generator,\nrectifier, rectifier diode, etc.) status, displays load voltage, unloaded\nvoltage, ripple status, charging system status, thus to find out whether the\noutput voltage of the generator is normal, the rectifier diode works properly\nor not, which avoids damaging the battery and shortening its life greatly due\nto overcharging or incomplete charging. Monitor Real-time Voltage BA301\nbattery tester can monitors real-time voltage to check battery health status.\nThere's a hot-key to directly one-click read the voltage change graph. The\nwaveform displays current voltage, maximum, and minimum voltage during\nignition, and it will stay static until there are voltage changes detected. By\nanalyzing the voltage of discharge, starting, and charging to know if the\nbattery needs to be replaced or not. Read more Battery Type Coverage This load\ntester can detect all automotive 6V\u0026amp;12V lead-acid batteries, such as regular\nflooded, AGM flat plate, AGM spiral, GEL, and EFB batteries of motorcycle,\nboat, vehicle, light truck and more. It gives you accurate test results in\nmerely seconds based on CCA, BCI, CA, MCA, JIS, DIN, IEC, EN, SAE battery\nrating standards Battery Location Supported Two test models “IN VEHICLE” and\n“OUT OF VEHICLE” allow you to test the battery according to its location,\nprovide you with more accurate test results quickly, thus replacing the bad\ncell in time. Designed with a large easy-to-read color LCD screen and user-\nfriendly navigation menu, even a beginner can use it at ease. Free Update \u0026amp;\nPrint Able to store, review, and transfer the test results and multiple\nvoltage waveform graphs to a computer for printing and further analysis.\nLifetime free update via software online available. Download the software on\nANCEL official website, and it supports Windows XP\/7\/8\/10 operating systems,\nnot compatible with Mac OS and Linux. Read more Read more BST200 12V Battery\nTester BA101 12V Battery Tester BA201 12V Battery Tester BA301 6\/12V Battery\nTester BST500 12\/24V Battery Tester PB100 Circuit Tester Test Voltage 12V 12V\n12V 6V\/12V 12V\/24V 12V\/24V Application Check \u0026amp; Analyze 12V Lead-acid Battery\nCheck \u0026amp; Analyze 12V Lead-acid Battery Check \u0026amp; Analyze 12V Lead-acid Battery\nCheck \u0026amp; Analyze 6V\/12V Lead-acid Battery Check \u0026amp; Analyze 12V\/24V Lead-acid\nBattery Check Automotive Electrical System Test Range 100-1100CCA 100-2000CCA\n100-2000CCA 100-2000CCA 100-2000CCA 12V\/24V Source Battery Standards Supported\nCCA, CA, MCA, JIS, DIN, IEC, EN, SAE AH, CCA, BCI, CA, MCA, JIS, DIN, IEC, EN,\nSAE, GB CCA, BCI, CA, MCA, JIS, DIN, IEC, EN, SAE CCA, BCI, CA, MCA, JIS, DIN,\nIEC, EN, SAE CCA, BCI, CA, MCA, JIS, DIN, IEC, EN, SAE, GB 4 working modes:\nDC\/AC voltage\/Resistance\/Diode Test Cranking System Test regular flooded, AGM\nflat plate, AGM spiral, GEL battery Cranking time, voltage and status Cranking\ntime, voltage and status Cranking time, voltage and status Storage battery\ntest,Maximum load system test Continuity test\/Activate components\/Voltage \u0026amp;\npolarity\/Signal circuit test etc. Test Charging System Test result: SOH, SOC,\nCCA value, CCA rating, voltage, internal resistance, etc. Load voltage,\nunloaded voltage, ripple status, charging system status Load voltage, unloaded\nvoltage, ripple status, charging system status Load voltage, unloaded voltage,\nripple status, charging system status Engine system activation load test,\nCharging system test Feature red\/green polarity indicators, follow \u0026amp; locate\nshort circuit, check bad Ground contacts Real-time Voltage Waveform Features\n\"Quick Test\" with AH value ✓ ✓ Testing trailer lights and connections Print\nData ✓ ✓ ✓ Built-in thermal printer Circuit breaker protection Internet Update\n✓ ✓ 20 feet extension cord\u003c\/p\u003e \n\n\u003ch3\u003eProduct Features\u003c\/h3\u003e\n \u003cul class=\"a\"\u003e\n \u003cli\u003eWorks on all 6V \u0026amp; 12V 100 - 2000 CCA lead-acid batteries, including regular flooded, AGM flat plate, AGM spiral, GEL, and EFB batteries for the Lawn Mower, motorcycle, car, light truck, boat, etc. Supports the majority of battery standards, such as CCA, BCI, CA, MCA, JIS, DIN, IEC, EN, SAE.\u003c\/li\u003e\n \u003cli\u003eCapacity for analyzing battery health status and quickly providing more accurate test results in merely seconds based on battery location in-vehicle or out-of vehicle, displays voltage value, standard CCA, measured CCA, SOH(%), SOC(%), internal resistance and more.\u003c\/li\u003e\n \u003cli\u003eAnalyzes starter cranking and alternator charging condition. Cranking test to test and analyze the starting motor (cranking time, voltage, and status), and the charging test to check and analyze the charging system (load voltage, unloaded voltage, ripple status, charging system status).\u003c\/li\u003e\n \u003cli\u003eFeatures one-click \"waveform\" to record the voltage changes (current voltage, maximum and minimum voltage) in a graph during ignition. You'll know if the battery needs to be replaced or not through analyzing the values of discharge voltage, starting voltage, and charging voltage.\u003c\/li\u003e\n \u003cli\u003eDesigned with 3 LED lights in green, yellow, red representing different health statuses of the battery. Able to store, review and transfer the test results to computer for printing and further analysis, free lifetime update available.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n\n\n\n","published_at":"2021-05-05T20:54:36+10:00","created_at":"2021-05-05T20:54:36+10:00","vendor":"ANCEL","type":"Battery Testers","tags":["autolisted"],"price":7238,"price_min":7238,"price_max":7238,"available":false,"price_varies":false,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":39332888576063,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"B08F9SBXN9","requires_shipping":true,"taxable":true,"featured_image":null,"available":false,"name":"ANCEL BA301 6V 12V Battery Load Tester Car Alternator Analyzer Cranking Charging System Test Tool for Motorcycle Car Boat Light Truck and More","public_title":null,"options":["Default Title"],"price":7238,"weight":386,"compare_at_price":null,"inventory_quantity":0,"inventory_management":"shopify","inventory_policy":"deny","barcode":"BA301","requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/cdn.shopify.com\/s\/files\/1\/1504\/3080\/products\/715AIeY_2BBVL.jpg?v=1620212076","\/\/cdn.shopify.com\/s\/files\/1\/1504\/3080\/products\/71-p0jOdBQL.jpg?v=1620212076","\/\/cdn.shopify.com\/s\/files\/1\/1504\/3080\/products\/71IiOKeLQJL.jpg?v=1620212077","\/\/cdn.shopify.com\/s\/files\/1\/1504\/3080\/products\/71Sxsms3eFL.jpg?v=1620212077","\/\/cdn.shopify.com\/s\/files\/1\/1504\/3080\/products\/71mEfRzNyLL.jpg?v=1620212077","\/\/cdn.shopify.com\/s\/files\/1\/1504\/3080\/products\/71pk6LLeA3L.jpg?v=1620212077","\/\/cdn.shopify.com\/s\/files\/1\/1504\/3080\/products\/81RZofsRvoL.jpg?v=1620212077"],"featured_image":"\/\/cdn.shopify.com\/s\/files\/1\/1504\/3080\/products\/715AIeY_2BBVL.jpg?v=1620212076","options":["Title"],"media":[{"alt":null,"id":20557689192511,"position":1,"preview_image":{"aspect_ratio":1.0,"height":1500,"width":1500,"src":"https:\/\/cdn.shopify.com\/s\/files\/1\/1504\/3080\/products\/715AIeY_2BBVL.jpg?v=1620212076"},"aspect_ratio":1.0,"height":1500,"media_type":"image","src":"https:\/\/cdn.shopify.com\/s\/files\/1\/1504\/3080\/products\/715AIeY_2BBVL.jpg?v=1620212076","width":1500},{"alt":null,"id":20557689258047,"position":2,"preview_image":{"aspect_ratio":1.0,"height":1500,"width":1500,"src":"https:\/\/cdn.shopify.com\/s\/files\/1\/1504\/3080\/products\/71-p0jOdBQL.jpg?v=1620212076"},"aspect_ratio":1.0,"height":1500,"media_type":"image","src":"https:\/\/cdn.shopify.com\/s\/files\/1\/1504\/3080\/products\/71-p0jOdBQL.jpg?v=1620212076","width":1500},{"alt":null,"id":20557689323583,"position":3,"preview_image":{"aspect_ratio":1.0,"height":1500,"width":1500,"src":"https:\/\/cdn.shopify.com\/s\/files\/1\/1504\/3080\/products\/71IiOKeLQJL.jpg?v=1620212076"},"aspect_ratio":1.0,"height":1500,"media_type":"image","src":"https:\/\/cdn.shopify.com\/s\/files\/1\/1504\/3080\/products\/71IiOKeLQJL.jpg?v=1620212076","width":1500},{"alt":null,"id":20557689389119,"position":4,"preview_image":{"aspect_ratio":1.0,"height":1500,"width":1500,"src":"https:\/\/cdn.shopify.com\/s\/files\/1\/1504\/3080\/products\/71Sxsms3eFL.jpg?v=1620212077"},"aspect_ratio":1.0,"height":1500,"media_type":"image","src":"https:\/\/cdn.shopify.com\/s\/files\/1\/1504\/3080\/products\/71Sxsms3eFL.jpg?v=1620212077","width":1500},{"alt":null,"id":20557689454655,"position":5,"preview_image":{"aspect_ratio":1.0,"height":1800,"width":1800,"src":"https:\/\/cdn.shopify.com\/s\/files\/1\/1504\/3080\/products\/71mEfRzNyLL.jpg?v=1620212077"},"aspect_ratio":1.0,"height":1800,"media_type":"image","src":"https:\/\/cdn.shopify.com\/s\/files\/1\/1504\/3080\/products\/71mEfRzNyLL.jpg?v=1620212077","width":1800},{"alt":null,"id":20557689487423,"position":6,"preview_image":{"aspect_ratio":1.0,"height":1500,"width":1500,"src":"https:\/\/cdn.shopify.com\/s\/files\/1\/1504\/3080\/products\/71pk6LLeA3L.jpg?v=1620212077"},"aspect_ratio":1.0,"height":1500,"media_type":"image","src":"https:\/\/cdn.shopify.com\/s\/files\/1\/1504\/3080\/products\/71pk6LLeA3L.jpg?v=1620212077","width":1500},{"alt":null,"id":20557689520191,"position":7,"preview_image":{"aspect_ratio":1.0,"height":1500,"width":1500,"src":"https:\/\/cdn.shopify.com\/s\/files\/1\/1504\/3080\/products\/81RZofsRvoL.jpg?v=1620212077"},"aspect_ratio":1.0,"height":1500,"media_type":"image","src":"https:\/\/cdn.shopify.com\/s\/files\/1\/1504\/3080\/products\/81RZofsRvoL.jpg?v=1620212077","width":1500}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"\u003ch3\u003eANCEL BA301 6V 12V Battery Load Tester Car Alternator Analyzer Cranking Charging System Test Tool for Motorcycle Car Boat Light Truck and More\u003c\/h3\u003e\n\u003cp id=\"b\"\u003eANCEL BA301 battery tester adopts the state-of-the-art\nconductance testing technology to measure the actual cold cranking amps\ncapability of starting battery, battery health status, and common fault of\nstarting system and charging system quickly and accurately. It works on all\nautomotive 6V \u0026amp; 12V 100-2000 CCA lead-acid batteries of car, motorcycle, light\ntruck, and more, including regular flooded, AGM flat plate, AGM spiral, GEL,\nand EFB batteries. And it features the \"Waveform\" menu and a hot-key on the\ndevice to monitors real-time voltage. This tool lets you know the battery\nstatus in advance and replace with a new battery in time, save a trip, and\nmoney to an auto repair shop. The test result includes 5 kinds of battery\nstatus and possible causes: 1. Good Battery The battery is without any\nproblem, please be relaxed to use. 2. Good, Recharge Good battery but low\ncurrent, recharge before using. 3. Replace The battery is near to or already\nreached the end of the using life, please replace the battery. Otherwise,\nbigger danger will be followed. 4. Bad cell, Replace Battery interior damaged,\nbad cell or short circuit, replace battery. 5. Charge, Retest Unstable battery\nshall be recharged and retested to avoid error. If the same test result\nappears after recharge and retest, the battery is regarded as damaged, replace\nthe battery. BATTERY CHECK Check 6V Motorcycle Battery BA301 battery analyzer\nworks on not the 12V battery of the automotive but also the 6V battery of the\nmotorcycle. Select motorcycle battery model and it takes around 1 second to\ndisplay the test result, including battery condition, the status of health,\ninternal resistance(mΩ), measured CCA, standard battery model, voltage value.\nANCEL BA301 Battery Tester Highlights: 1. Work on 6V \u0026amp; 12V 100-2000 CCA\nbattery 2. Check battery health status 3. Cranking test \u0026amp; Charging test 4.\nMonitor real-time voltage in Waveform 5. Get a accurate test results in merely\nseconds 6. Able to store, review, print the test result 7. Voltage measurement\nrange: 6-16V DC 8. Free lifetime update CANNOT test lithium battery and solar\nbattery No internal battery required and gets power directly from the detected\nbattery Test the battery with loss of electricity directly, a full charge is\nnot required before testing Read more Cranking Test The cranking test is used\nto test and analyze the actual required cranking current and cranking voltage\nto check the starting motor works properly or not. The test result displays\ncranking time, voltage, and status. If the stating malfunction may cause an\nincreased starting loaded torque; or rotor friction of the starting motor\ngenerates increasing friction of the starting motor itself Charging Test\nCharging test is used to check and analyze the charging system (generator,\nrectifier, rectifier diode, etc.) status, displays load voltage, unloaded\nvoltage, ripple status, charging system status, thus to find out whether the\noutput voltage of the generator is normal, the rectifier diode works properly\nor not, which avoids damaging the battery and shortening its life greatly due\nto overcharging or incomplete charging. Monitor Real-time Voltage BA301\nbattery tester can monitors real-time voltage to check battery health status.\nThere's a hot-key to directly one-click read the voltage change graph. The\nwaveform displays current voltage, maximum, and minimum voltage during\nignition, and it will stay static until there are voltage changes detected. By\nanalyzing the voltage of discharge, starting, and charging to know if the\nbattery needs to be replaced or not. Read more Battery Type Coverage This load\ntester can detect all automotive 6V\u0026amp;12V lead-acid batteries, such as regular\nflooded, AGM flat plate, AGM spiral, GEL, and EFB batteries of motorcycle,\nboat, vehicle, light truck and more. It gives you accurate test results in\nmerely seconds based on CCA, BCI, CA, MCA, JIS, DIN, IEC, EN, SAE battery\nrating standards Battery Location Supported Two test models “IN VEHICLE” and\n“OUT OF VEHICLE” allow you to test the battery according to its location,\nprovide you with more accurate test results quickly, thus replacing the bad\ncell in time. Designed with a large easy-to-read color LCD screen and user-\nfriendly navigation menu, even a beginner can use it at ease. Free Update \u0026amp;\nPrint Able to store, review, and transfer the test results and multiple\nvoltage waveform graphs to a computer for printing and further analysis.\nLifetime free update via software online available. Download the software on\nANCEL official website, and it supports Windows XP\/7\/8\/10 operating systems,\nnot compatible with Mac OS and Linux. Read more Read more BST200 12V Battery\nTester BA101 12V Battery Tester BA201 12V Battery Tester BA301 6\/12V Battery\nTester BST500 12\/24V Battery Tester PB100 Circuit Tester Test Voltage 12V 12V\n12V 6V\/12V 12V\/24V 12V\/24V Application Check \u0026amp; Analyze 12V Lead-acid Battery\nCheck \u0026amp; Analyze 12V Lead-acid Battery Check \u0026amp; Analyze 12V Lead-acid Battery\nCheck \u0026amp; Analyze 6V\/12V Lead-acid Battery Check \u0026amp; Analyze 12V\/24V Lead-acid\nBattery Check Automotive Electrical System Test Range 100-1100CCA 100-2000CCA\n100-2000CCA 100-2000CCA 100-2000CCA 12V\/24V Source Battery Standards Supported\nCCA, CA, MCA, JIS, DIN, IEC, EN, SAE AH, CCA, BCI, CA, MCA, JIS, DIN, IEC, EN,\nSAE, GB CCA, BCI, CA, MCA, JIS, DIN, IEC, EN, SAE CCA, BCI, CA, MCA, JIS, DIN,\nIEC, EN, SAE CCA, BCI, CA, MCA, JIS, DIN, IEC, EN, SAE, GB 4 working modes:\nDC\/AC voltage\/Resistance\/Diode Test Cranking System Test regular flooded, AGM\nflat plate, AGM spiral, GEL battery Cranking time, voltage and status Cranking\ntime, voltage and status Cranking time, voltage and status Storage battery\ntest,Maximum load system test Continuity test\/Activate components\/Voltage \u0026amp;\npolarity\/Signal circuit test etc. Test Charging System Test result: SOH, SOC,\nCCA value, CCA rating, voltage, internal resistance, etc. Load voltage,\nunloaded voltage, ripple status, charging system status Load voltage, unloaded\nvoltage, ripple status, charging system status Load voltage, unloaded voltage,\nripple status, charging system status Engine system activation load test,\nCharging system test Feature red\/green polarity indicators, follow \u0026amp; locate\nshort circuit, check bad Ground contacts Real-time Voltage Waveform Features\n\"Quick Test\" with AH value ✓ ✓ Testing trailer lights and connections Print\nData ✓ ✓ ✓ Built-in thermal printer Circuit breaker protection Internet Update\n✓ ✓ 20 feet extension cord\u003c\/p\u003e \n\n\u003ch3\u003eProduct Features\u003c\/h3\u003e\n \u003cul class=\"a\"\u003e\n \u003cli\u003eWorks on all 6V \u0026amp; 12V 100 - 2000 CCA lead-acid batteries, including regular flooded, AGM flat plate, AGM spiral, GEL, and EFB batteries for the Lawn Mower, motorcycle, car, light truck, boat, etc. Supports the majority of battery standards, such as CCA, BCI, CA, MCA, JIS, DIN, IEC, EN, SAE.\u003c\/li\u003e\n \u003cli\u003eCapacity for analyzing battery health status and quickly providing more accurate test results in merely seconds based on battery location in-vehicle or out-of vehicle, displays voltage value, standard CCA, measured CCA, SOH(%), SOC(%), internal resistance and more.\u003c\/li\u003e\n \u003cli\u003eAnalyzes starter cranking and alternator charging condition. Cranking test to test and analyze the starting motor (cranking time, voltage, and status), and the charging test to check and analyze the charging system (load voltage, unloaded voltage, ripple status, charging system status).\u003c\/li\u003e\n \u003cli\u003eFeatures one-click \"waveform\" to record the voltage changes (current voltage, maximum and minimum voltage) in a graph during ignition. You'll know if the battery needs to be replaced or not through analyzing the values of discharge voltage, starting voltage, and charging voltage.\u003c\/li\u003e\n \u003cli\u003eDesigned with 3 LED lights in green, yellow, red representing different health statuses of the battery. Able to store, review and transfer the test results to computer for printing and further analysis, free lifetime update available.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n\n\n\n"}

ANCEL BA301 6V 12V Battery Load Tester Car Alternator Analyzer Cranking Charging System Test Tool for Motorcycle Car Boat Light Truck and More

In Stock. Leaves warehouse in 2-3 business days

Brand: ANCEL
$72.38 AUD
Maximum quantity available reached.
Free Shipping Australia Wide
100% Safe & Secure Checkout
100 Days Return Policy *
1 Year Warranty *

ANCEL BA301 6V 12V Battery Load Tester Car Alternator Analyzer Cranking Charging System Test Tool for Motorcycle Car Boat Light Truck and More

ANCEL BA301 battery tester adopts the state-of-the-art conductance testing technology to measure the actual cold cranking amps capability of starting battery, battery health status, and common fault of starting system and charging system quickly and accurately. It works on all automotive 6V & 12V 100-2000 CCA lead-acid batteries of car, motorcycle, light truck, and more, including regular flooded, AGM flat plate, AGM spiral, GEL, and EFB batteries. And it features the "Waveform" menu and a hot-key on the device to monitors real-time voltage. This tool lets you know the battery status in advance and replace with a new battery in time, save a trip, and money to an auto repair shop. The test result includes 5 kinds of battery status and possible causes: 1. Good Battery The battery is without any problem, please be relaxed to use. 2. Good, Recharge Good battery but low current, recharge before using. 3. Replace The battery is near to or already reached the end of the using life, please replace the battery. Otherwise, bigger danger will be followed. 4. Bad cell, Replace Battery interior damaged, bad cell or short circuit, replace battery. 5. Charge, Retest Unstable battery shall be recharged and retested to avoid error. If the same test result appears after recharge and retest, the battery is regarded as damaged, replace the battery. BATTERY CHECK Check 6V Motorcycle Battery BA301 battery analyzer works on not the 12V battery of the automotive but also the 6V battery of the motorcycle. Select motorcycle battery model and it takes around 1 second to display the test result, including battery condition, the status of health, internal resistance(mΩ), measured CCA, standard battery model, voltage value. ANCEL BA301 Battery Tester Highlights: 1. Work on 6V & 12V 100-2000 CCA battery 2. Check battery health status 3. Cranking test & Charging test 4. Monitor real-time voltage in Waveform 5. Get a accurate test results in merely seconds 6. Able to store, review, print the test result 7. Voltage measurement range: 6-16V DC 8. Free lifetime update CANNOT test lithium battery and solar battery No internal battery required and gets power directly from the detected battery Test the battery with loss of electricity directly, a full charge is not required before testing Read more Cranking Test The cranking test is used to test and analyze the actual required cranking current and cranking voltage to check the starting motor works properly or not. The test result displays cranking time, voltage, and status. If the stating malfunction may cause an increased starting loaded torque; or rotor friction of the starting motor generates increasing friction of the starting motor itself Charging Test Charging test is used to check and analyze the charging system (generator, rectifier, rectifier diode, etc.) status, displays load voltage, unloaded voltage, ripple status, charging system status, thus to find out whether the output voltage of the generator is normal, the rectifier diode works properly or not, which avoids damaging the battery and shortening its life greatly due to overcharging or incomplete charging. Monitor Real-time Voltage BA301 battery tester can monitors real-time voltage to check battery health status. There's a hot-key to directly one-click read the voltage change graph. The waveform displays current voltage, maximum, and minimum voltage during ignition, and it will stay static until there are voltage changes detected. By analyzing the voltage of discharge, starting, and charging to know if the battery needs to be replaced or not. Read more Battery Type Coverage This load tester can detect all automotive 6V&12V lead-acid batteries, such as regular flooded, AGM flat plate, AGM spiral, GEL, and EFB batteries of motorcycle, boat, vehicle, light truck and more. It gives you accurate test results in merely seconds based on CCA, BCI, CA, MCA, JIS, DIN, IEC, EN, SAE battery rating standards Battery Location Supported Two test models “IN VEHICLE” and “OUT OF VEHICLE” allow you to test the battery according to its location, provide you with more accurate test results quickly, thus replacing the bad cell in time. Designed with a large easy-to-read color LCD screen and user- friendly navigation menu, even a beginner can use it at ease. Free Update & Print Able to store, review, and transfer the test results and multiple voltage waveform graphs to a computer for printing and further analysis. Lifetime free update via software online available. Download the software on ANCEL official website, and it supports Windows XP/7/8/10 operating systems, not compatible with Mac OS and Linux. Read more Read more BST200 12V Battery Tester BA101 12V Battery Tester BA201 12V Battery Tester BA301 6/12V Battery Tester BST500 12/24V Battery Tester PB100 Circuit Tester Test Voltage 12V 12V 12V 6V/12V 12V/24V 12V/24V Application Check & Analyze 12V Lead-acid Battery Check & Analyze 12V Lead-acid Battery Check & Analyze 12V Lead-acid Battery Check & Analyze 6V/12V Lead-acid Battery Check & Analyze 12V/24V Lead-acid Battery Check Automotive Electrical System Test Range 100-1100CCA 100-2000CCA 100-2000CCA 100-2000CCA 100-2000CCA 12V/24V Source Battery Standards Supported CCA, CA, MCA, JIS, DIN, IEC, EN, SAE AH, CCA, BCI, CA, MCA, JIS, DIN, IEC, EN, SAE, GB CCA, BCI, CA, MCA, JIS, DIN, IEC, EN, SAE CCA, BCI, CA, MCA, JIS, DIN, IEC, EN, SAE CCA, BCI, CA, MCA, JIS, DIN, IEC, EN, SAE, GB 4 working modes: DC/AC voltage/Resistance/Diode Test Cranking System Test regular flooded, AGM flat plate, AGM spiral, GEL battery Cranking time, voltage and status Cranking time, voltage and status Cranking time, voltage and status Storage battery test,Maximum load system test Continuity test/Activate components/Voltage & polarity/Signal circuit test etc. Test Charging System Test result: SOH, SOC, CCA value, CCA rating, voltage, internal resistance, etc. Load voltage, unloaded voltage, ripple status, charging system status Load voltage, unloaded voltage, ripple status, charging system status Load voltage, unloaded voltage, ripple status, charging system status Engine system activation load test, Charging system test Feature red/green polarity indicators, follow & locate short circuit, check bad Ground contacts Real-time Voltage Waveform Features "Quick Test" with AH value ✓ ✓ Testing trailer lights and connections Print Data ✓ ✓ ✓ Built-in thermal printer Circuit breaker protection Internet Update ✓ ✓ 20 feet extension cord

Product Features

  • Works on all 6V & 12V 100 - 2000 CCA lead-acid batteries, including regular flooded, AGM flat plate, AGM spiral, GEL, and EFB batteries for the Lawn Mower, motorcycle, car, light truck, boat, etc. Supports the majority of battery standards, such as CCA, BCI, CA, MCA, JIS, DIN, IEC, EN, SAE.
  • Capacity for analyzing battery health status and quickly providing more accurate test results in merely seconds based on battery location in-vehicle or out-of vehicle, displays voltage value, standard CCA, measured CCA, SOH(%), SOC(%), internal resistance and more.
  • Analyzes starter cranking and alternator charging condition. Cranking test to test and analyze the starting motor (cranking time, voltage, and status), and the charging test to check and analyze the charging system (load voltage, unloaded voltage, ripple status, charging system status).
  • Features one-click "waveform" to record the voltage changes (current voltage, maximum and minimum voltage) in a graph during ignition. You'll know if the battery needs to be replaced or not through analyzing the values of discharge voltage, starting voltage, and charging voltage.
  • Designed with 3 LED lights in green, yellow, red representing different health statuses of the battery. Able to store, review and transfer the test results to computer for printing and further analysis, free lifetime update available.

Buy with confidence as this product comes with 18 months full local warranty in Australia & New Zealand (unless otherwise stated in the overview).

This product also comes with the benefits of the CocoonPower Warranty. For further details please read our Warranty Guidelines.

You can also purchase 3 Year Extended Care. If you are interested please see our Extended Care Information.

Related Products