Enter SPECIAL5 at Checkout for 5% OFF & Free Shipping Australia Wide

{"id":1620921057325,"title":"BJC LC-1 Stereo Audio Cables, 6 foot","handle":"bjc-lc-1-stereo-audio-cables-6-foot","description":"\u003ch3\u003eBJC LC-1 Stereo Audio Cables, 6 foot\u003c\/h3\u003e\u003cp id=\"b\"\u003e\u003cb\u003eBlue Jeans Cable LC-1 Stereo Audio Cables, 6 foot\u003c\/b\u003e \u003cbr\u003e \u003cbr\u003e This pair of stereo audio cables is manufactured by Blue Jeans Cable in our assembly shop in Seattle, Washington. The cable stock, LC-1, is our own proprietary design: a low-capacitance cable with a pair of heavy 95% coverage bare copper shield braids for the maximum in low-frequency noise rejection. The two cables in the pair are separate--not joined to one another--for high flexibility. \u003cbr\u003e \u003cbr\u003e \u003cb\u003eWhat Makes a Good Audio Cable?\u003c\/b\u003e \u003cbr\u003e \u003cbr\u003eThere's a lot of nonsense on the internet about fancy analog audio cables; the reality is that the requirements for unbalanced (or, if you like, \"RCA\") audio cable are very simple, if seldom properly addressed. As a high-impedance circuit, an analog audio signal is subject to high-frequency rolloff from excess capacitance, which is caused by conductors being too near each other or separated by a low-quality dielectric. And because unbalanced audio is not balanced, there is no common-mode noise rejection; noise rejection depends entirely upon shield effectiveness. \u003cbr\u003e \u003cbr\u003e \u003cb\u003eThe LC-1 Design\u003c\/b\u003e \u003cbr\u003e \u003cbr\u003eWe designed LC-1 with a small center conductor and a large diameter PE foam (or, if you prefer fancy terms, \"nitrogen-injected\") dielectric, resulting in extremely low capacitance -- about 12.2 pF\/foot. Outside of that dielectric, we put two bare copper shield braids, each with 95% coverage; at audio frequencies, braid is far more effective than foil, and this is as heavy a shield as you'll find on any audio interconnect. \u003cbr\u003e \u003cbr\u003e \u003cb\u003eDesigned, Cabled and Assembled in the USA\u003c\/b\u003e \u003cbr\u003e \u003cbr\u003eThe bulk cable stock is made to our design by Belden in Richmond, Indiana, and we assemble these cables in our shop in Seattle, Washington.\u003c\/p\u003e\u003ch3\u003eProduct Features\u003c\/h3\u003e\u003cul class=\"a\"\u003e \u003cli\u003eLow capacitance -- 12 pF\/foot -- prevents high frequency rolloff\u003c\/li\u003e \u003cli\u003eDouble bare copper braid shielding provides the best in EMI rejection available in an unbalanced (RCA) cable design\u003c\/li\u003e \u003cli\u003eTaversoe RCA plugs provide a firm grip on jacks without the over-tight grasp that can damage equipment\u003c\/li\u003e \u003cli\u003eAssembled in the US from US-made cable and imported connectors\u003c\/li\u003e \u003cli\u003eCM rated (higher than CL2\/3), making it legal for in-wall installation in NEC jurisdictions\u003c\/li\u003e\n\u003c\/ul\u003e","published_at":"2019-03-08T11:09:41+11:00","created_at":"2019-03-08T11:09:41+11:00","vendor":"Blue Jeans Cable","type":"RCA Cables","tags":["Accessories \u0026 Supplies","Audio \u0026 Video Accessories","Audio Cables","Cables \u0026 Interconnects","cp19383","cp220","RCA Cables"],"price":23000,"price_min":23000,"price_max":23000,"available":true,"price_varies":false,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":14370354200621,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"B00NAJ9I24","requires_shipping":true,"taxable":true,"featured_image":null,"available":true,"name":"BJC LC-1 Stereo Audio Cables, 6 foot","public_title":null,"options":["Default Title"],"price":23000,"weight":360,"compare_at_price":null,"inventory_quantity":10,"inventory_management":"shopify","inventory_policy":"deny","barcode":"811887013935"}],"images":["\/\/cdn.shopify.com\/s\/files\/1\/1504\/3080\/products\/61poS0ZPs5L._SL1500.jpg?v=1571709882"],"featured_image":"\/\/cdn.shopify.com\/s\/files\/1\/1504\/3080\/products\/61poS0ZPs5L._SL1500.jpg?v=1571709882","options":["Title"],"media":[{"alt":null,"id":3506159026239,"position":1,"preview_image":{"aspect_ratio":1.0,"height":1500,"width":1500,"src":"https:\/\/cdn.shopify.com\/s\/files\/1\/1504\/3080\/products\/61poS0ZPs5L._SL1500.jpg?v=1570426070"},"aspect_ratio":1.0,"height":1500,"media_type":"image","src":"https:\/\/cdn.shopify.com\/s\/files\/1\/1504\/3080\/products\/61poS0ZPs5L._SL1500.jpg?v=1570426070","width":1500}],"content":"\u003ch3\u003eBJC LC-1 Stereo Audio Cables, 6 foot\u003c\/h3\u003e\u003cp id=\"b\"\u003e\u003cb\u003eBlue Jeans Cable LC-1 Stereo Audio Cables, 6 foot\u003c\/b\u003e \u003cbr\u003e \u003cbr\u003e This pair of stereo audio cables is manufactured by Blue Jeans Cable in our assembly shop in Seattle, Washington. The cable stock, LC-1, is our own proprietary design: a low-capacitance cable with a pair of heavy 95% coverage bare copper shield braids for the maximum in low-frequency noise rejection. The two cables in the pair are separate--not joined to one another--for high flexibility. \u003cbr\u003e \u003cbr\u003e \u003cb\u003eWhat Makes a Good Audio Cable?\u003c\/b\u003e \u003cbr\u003e \u003cbr\u003eThere's a lot of nonsense on the internet about fancy analog audio cables; the reality is that the requirements for unbalanced (or, if you like, \"RCA\") audio cable are very simple, if seldom properly addressed. As a high-impedance circuit, an analog audio signal is subject to high-frequency rolloff from excess capacitance, which is caused by conductors being too near each other or separated by a low-quality dielectric. And because unbalanced audio is not balanced, there is no common-mode noise rejection; noise rejection depends entirely upon shield effectiveness. \u003cbr\u003e \u003cbr\u003e \u003cb\u003eThe LC-1 Design\u003c\/b\u003e \u003cbr\u003e \u003cbr\u003eWe designed LC-1 with a small center conductor and a large diameter PE foam (or, if you prefer fancy terms, \"nitrogen-injected\") dielectric, resulting in extremely low capacitance -- about 12.2 pF\/foot. Outside of that dielectric, we put two bare copper shield braids, each with 95% coverage; at audio frequencies, braid is far more effective than foil, and this is as heavy a shield as you'll find on any audio interconnect. \u003cbr\u003e \u003cbr\u003e \u003cb\u003eDesigned, Cabled and Assembled in the USA\u003c\/b\u003e \u003cbr\u003e \u003cbr\u003eThe bulk cable stock is made to our design by Belden in Richmond, Indiana, and we assemble these cables in our shop in Seattle, Washington.\u003c\/p\u003e\u003ch3\u003eProduct Features\u003c\/h3\u003e\u003cul class=\"a\"\u003e \u003cli\u003eLow capacitance -- 12 pF\/foot -- prevents high frequency rolloff\u003c\/li\u003e \u003cli\u003eDouble bare copper braid shielding provides the best in EMI rejection available in an unbalanced (RCA) cable design\u003c\/li\u003e \u003cli\u003eTaversoe RCA plugs provide a firm grip on jacks without the over-tight grasp that can damage equipment\u003c\/li\u003e \u003cli\u003eAssembled in the US from US-made cable and imported connectors\u003c\/li\u003e \u003cli\u003eCM rated (higher than CL2\/3), making it legal for in-wall installation in NEC jurisdictions\u003c\/li\u003e\n\u003c\/ul\u003e"}

BJC LC-1 Stereo Audio Cables, 6 foot

In Stock. Leaves warehouse in 2-3 business days

$230.00
Maximum quantity available reached.
Free Shipping Australia Wide
100% Safe & Secure Checkout
100 Days Return Policy *
1 Year Warranty *

BJC LC-1 Stereo Audio Cables, 6 foot

Blue Jeans Cable LC-1 Stereo Audio Cables, 6 foot

This pair of stereo audio cables is manufactured by Blue Jeans Cable in our assembly shop in Seattle, Washington. The cable stock, LC-1, is our own proprietary design: a low-capacitance cable with a pair of heavy 95% coverage bare copper shield braids for the maximum in low-frequency noise rejection. The two cables in the pair are separate--not joined to one another--for high flexibility.

What Makes a Good Audio Cable?

There's a lot of nonsense on the internet about fancy analog audio cables; the reality is that the requirements for unbalanced (or, if you like, "RCA") audio cable are very simple, if seldom properly addressed. As a high-impedance circuit, an analog audio signal is subject to high-frequency rolloff from excess capacitance, which is caused by conductors being too near each other or separated by a low-quality dielectric. And because unbalanced audio is not balanced, there is no common-mode noise rejection; noise rejection depends entirely upon shield effectiveness.

The LC-1 Design

We designed LC-1 with a small center conductor and a large diameter PE foam (or, if you prefer fancy terms, "nitrogen-injected") dielectric, resulting in extremely low capacitance -- about 12.2 pF/foot. Outside of that dielectric, we put two bare copper shield braids, each with 95% coverage; at audio frequencies, braid is far more effective than foil, and this is as heavy a shield as you'll find on any audio interconnect.

Designed, Cabled and Assembled in the USA

The bulk cable stock is made to our design by Belden in Richmond, Indiana, and we assemble these cables in our shop in Seattle, Washington.

Product Features

  • Low capacitance -- 12 pF/foot -- prevents high frequency rolloff
  • Double bare copper braid shielding provides the best in EMI rejection available in an unbalanced (RCA) cable design
  • Taversoe RCA plugs provide a firm grip on jacks without the over-tight grasp that can damage equipment
  • Assembled in the US from US-made cable and imported connectors
  • CM rated (higher than CL2/3), making it legal for in-wall installation in NEC jurisdictions

Buy with confidence as this product comes with 18 months full local warranty in Australia & New Zealand (unless otherwise stated in the overview).

This product also comes with the benefits of the CocoonPower Warranty. For further details please read our Warranty Guidelines.

You can also purchase 3 Year Extended Care. If you are interested please see our Extended Care Information.

Related Products